Hempel CONVERSION PRIMER Light Red
Switch from old antifouling to a biocide-free surface using a correctly prepared tiecoat. Hempel Conversion Primer is a two-component epoxy intermediate coat over sound antifouling and between epoxy priming and Hempaspeed TF. It is also suitable as a base in the Silic One system before Tiecoat. Planning the coating intervals is important because the next product has its own precise adhesion window.
Varastossa
View product colour samples+×
Hempel CONVERSION PRIMER Light Red · colour samples for this product.
- 50711Light Red
Screen colours are indicative; check the colour before painting.
Calculate how much you need +
Hempel CONVERSION PRIMER Light Red
Enter the area to see how much paint and how many tins you need.
Calculation: 15.0 m²/l/coat. Actual consumption may be higher. Select the number of coats for your project: one coat is usually not enough for a complete treatment of a new surface. Other products in the system are not included in the calculation.
View product informationFree collection from our store · 14-day right of withdrawal – see terms
Hempel Conversion Primer makes it easier to switch from conventional antifouling paint to a biocide-free hull coating. It is a two-component epoxy paint that forms a tiecoat over correctly prepared and firmly adhering existing antifouling. Another application is to provide adhesion between epoxy priming and the Hempaspeed TF topcoat.
Do not apply Conversion Primer directly to bare hull material. First prepare and prime a new or stripped hull with a suitable system. Retaining old antifouling in poor condition does not simplify the work if the underlying layer cannot support the new coating: remove flaking paint and repair exposed areas before applying the tiecoat.
Choose the next product before mixing the components. Hempaspeed TF and Silic One Tiecoat do not share the same overcoating interval. Hempaspeed's short adhesion window requires a manageable working area and tools ready for use. Pot life in the mixing container is not the same as the time an already painted surface can wait before the next coat.
Mix the base and curing agent in the correct ratio by volume and use the mixture without thinning. The product is free-flowing, so brush out runs immediately. Conversion Primer is an intermediate coat in the system and requires subsequent treatment with the chosen coating; it is not left as the boat's finished outer surface.
Detailed work instructions, the manufacturer’s product data sheets and downloadable materials are available on the Additional Information tab.
- Check the existing surface. Test paint adhesion with a steel scraper. Remove loose paint and dirt. Wet-sand a suitable surface, rinse and dry. Prime bare and filled areas according to the system. Do not apply directly to an unpainted substrate.
- Mix 3:1. Base 45445 : curing agent 95441 = 3:1 by volume. Mix thoroughly. Pot life at +20 °C is 8 h. Do not thin.
- Apply one coat. Apply 1 full unthinned coat by brush or roller. Brush out runs immediately. Reference film: 25 µm dry / 69 µm wet; theoretical coverage 15 m²/l.
- Maintain suitable conditions. Surface above +10 °C during application and curing, RH below 85 %. Provide ventilation and prevent moisture on the fresh surface.
- Continue within the selected product's interval. Conversion Primer → Hempaspeed TF: 30–65 min at the table temperatures of +10, +20 and +30 °C. → Silic One Tiecoat: +20 °C 2–4 h; +10 °C 4–8 h; +30 °C 1–2 h. The +10 °C reference value does not remove the requirement to work above +10 °C.
- Exceeding the interval and putting into service. The PDS instructs that a surface exceeding the maximum interval must be abraded. The Silic One Tiecoat system instructions require a new coat of primer if the adhesion window is exceeded; follow the complete selected system's instructions. Launching time is determined by the topcoat. Clean tools with Thinner 845; read the SDSs for both components.
Download the detailed work instructions and the manufacturer’s technical documents from the Additional Information tab.
Venemaalit.fi work instructions
Open work instructions (PDF) · FI / SV / EN ↗| Type | 2K epoxy tiecoat |
|---|---|
| Components / mixing ratio | 45445 + 95441 / 3:1 by volume |
| Pot life at +20 °C | 8 h |
| Thinning | Do not thin |
| Film thickness / coverage | 25 µm dry / 69 µm wet; 15 m²/l |
| Hempaspeed TF application | 30–65 min, table temperatures +10 / +20 / +30 °C |
| Tiecoat application at +20 °C | 2–4 h |
Downloadable materials
Manufacturer’s product data sheet, Finnish (PDF)
- Hempel Conversion Primer, base 45445 – safety data sheet 4544550711 (PDF)
- Hempel Conversion Primer, curing agent 95441 – safety data sheet 9544100000 (PDF)
Safety
The following information was checked against the Finland-specific safety data sheets linked above. Also check the labelling on your own package and all protective measures specified in the SDS.
Conversion Primer, base 45445: Danger.
- H226 – Flammable liquid and vapour.
- H315 – Causes skin irritation.
- H317 – May cause an allergic skin reaction.
- H318 – Causes serious eye damage.
- H335 – May cause respiratory irritation.
- H336 – May cause drowsiness or dizziness.
- H412 – Harmful to aquatic life with long lasting effects.
Conversion Primer, curing agent 95441: Danger.
- H226 – Flammable liquid and vapour.
- H315 – Causes skin irritation.
- H317 – May cause an allergic skin reaction.
- H318 – Causes serious eye damage.
- H332 – Harmful if inhaled.
- H412 – Harmful to aquatic life with long lasting effects.
Venemaalit.fi work instructions
Open work instructions (PDF) · FI / SV / EN ↗