Epifanes High Gloss Clear Varnish
Give your boat's woodwork a traditional high-gloss varnish finish. Epifanes High Gloss, also known as Clear Varnish, is a one-component UV-protected marine varnish for wood and plywood indoors and outdoors above the waterline. It is suitable for building a new varnish finish and maintaining sound existing varnish. Bare wood first receives thinned penetrating coats, followed by sufficient finishing coats.
Varastossa
Calculate how much you need +
Epifanes High Gloss Clear Varnish
Enter the area to see how much paint and how many tins you need.
14.0 m²/l/coat. Consumption is an approximate estimate for unthinned varnish. Thinning the initial coats can reduce the proportion of varnish in the applied mixture, but wood absorption, coat thickness and application losses affect actual consumption. The calculator does not automatically deduct the thinner proportion and does not include thinner. Select 1–6 coats for the stage being calculated. Follow the product-specific thinning, coat-count and drying instructions; six is not a universal limit for the complete varnish system.
View product informationFree collection from our store · 14-day right of withdrawal – see terms
Epifanes High Gloss Kirkaslakka is called Clear Varnish in the manufacturer's product data sheet. This classic one-component marine varnish forms a high-gloss finish that leaves the wood grain visible. Based on phenolic and alkyd resins and tung oil, it contains a UV filter. It is suitable for solid wood and plywood inside and outside the boat above the waterline.
For new varnishing, cleaning the surface and allowing the varnish to penetrate are part of the complete treatment. The first three coats are progressively thinned, after which the protective film is built up with several finishing coats. One thick coat does not replace this sequence. Apply with a soft, long-bristled brush and finish strokes along the wood grain.
For maintenance varnishing, clean and sand sound existing one- or two-component varnish and remove dust thoroughly. Remove loose or damaged varnish before further treatment. Do not apply directly to epoxy resin. For oily teak or iroko, consider the purpose-developed Woodfinish Gloss and follow its own system instructions.
High gloss also highlights unevenness in the substrate, so allow time for sanding between coats and drying. For an interior satin finish, Rubbed Effectcan be applied over the completed varnish system; for a matt finish indoors and outdoors, use Woodfinish Matte. The finishing varnish does not replace the protective film required underneath. Inspect varnish surfaces early during maintenance and apply maintenance coats before the film breaks down.
Detailed work instructions, the manufacturer’s product data sheets and downloadable materials are available on the Additional Information tab.
- Prepare the wood. Remove dirt and grease, dry, and sand bare wood with P220 paper along the grain. Sand clean, sound existing varnish with P240 paper. Remove dust. Do not apply directly to epoxy resin.
- Apply the penetrating coats. On new wood: 1 coat thinned 50 %, 1 coat thinned 25 % and 1 coat thinned 15 %. Use Epifanes Brushthinner for Paint & Varnish or a good-quality white spirit specified in the data sheet. Sand by hand with P220 between the initial stages and P280 after the third coat.
- Build the finishing film. Apply at least 4 finishing coats, thinned 0–5 %. Strong UV exposure requires at least 6 full finishing coats in the manufacturer's system. Use a soft, long-bristled brush; a roller is not recommended in this EU product data sheet.
- Allow to dry and sand. At +20 °C, apply the next coat no earlier than after 24 h. Cold conditions, a thick coat and poor ventilation extend the time. Lightly sand between finishing coats with P400 paper or a fine abrasive pad, and remove dust. Do not apply wet on wet.
- Maintain suitable conditions and care for the finish. Working temperature +8–30 °C, RH 50–85 %. Avoid direct sunlight and strong wind. Provide ventilation and follow the protective instructions on the package. Allow the film to dry sufficiently before use; inspect exterior surfaces regularly.
Download the detailed work instructions and the manufacturer’s technical documents from the Additional Information tab.
Venemaalit.fi work instructions
Open work instructions (PDF) · FI / SV / EN ↗| Type | 1K high-gloss wood varnish with UV filter |
|---|---|
| Use | Wood and plywood, indoors and outdoors above the waterline |
| Thinner for brush application | Epifanes Brushthinner / good-quality white spirit specified in the data sheet |
| New wood system | 3 progressively thinned coats + at least 4 finishing coats |
| Recoating at +20 °C | 24 h; conditions affect the time |
| Theoretical coverage | 15 m²/l, 35 µm dry film |
Downloadable materials
Venemaalit.fi work instructions
Open work instructions (PDF) · FI / SV / EN ↗